1. Neutral-start parking brake lever空档启动停车制动手柄；
2. 2.Track motors履带驱动马达；
3. 3.Hystat pumps hoses液压泵；
4. 4.Hydraulic oil cooler液压油冷却器；
5. 5.Service brakes行车制动器；
6. 6. hoses液压软管；
7. 7.Wet, multi-disc parking brakes湿式、多片停车制动器；
8. 8.Double reduction planetary final drives双级行星减速最终驱动装
置；
9. 9.hydraulic filters液压滤清器
8.2.6Standard Equipment Specifications标准装置规格类型与性能参数
1.Engine发动机：Type：Water-cooled, 4-stroke cycle类型：水冷，四冲程循环；Aspiration：Turbocharged充气形式：涡轮增压；Number of cylinders气缸数；Bore x stroke缸径x冲程；Piston displacement气缸排量：Governor： Mechanical, all-speed control调速器：机械式，全程调速；Horsepower rating @ 2400 rpm (SAE J1349)功率/2400 rpm（SAE标准： J1349）；Gross horsepower总功率；Net horsepower净功率；Meets EPA emissions regulations符合EPA排放规范；Fuel system：Direct injection供油系：直喷式；Lubrication system润滑系：Method：Gear pump, force-lubrication方式：齿轮泵，压力润滑；Filter：Full-flow滤清器：全流量；Air cleaner：Dry-type with double elements and dust evacuator, plus dust indicator空气滤清器：干式，双芯、排尘器、灰尘指示器配置
2. Transmission 传动装置：Torque converter：3-element, single-stage, single-phase变矩器：三元件，单级，单相；Transmission.：Full power shift, countershaft, automatic变速器：动力换档，副传动，自动型
3. Axles and Final Drives驱动桥与终传动：Drive system：Four-wheel
drive传动系统：四轮驱动；Front：Fixed, semi-floating前桥：固定式，半浮动轴；Rear：Center-pin support, semi-floating,24° total oscillation后桥：中心铰支承，半浮动轴，总摆动角24°；Reduction ge
ar：Spiral bevel gear减速齿轮：螺旋伞齿轮；Differential gear：Torque proportioning差速齿轮：转矩比例配合；Final reduction gear：Planetary gear, single reduction终减速齿轮：行星齿轮，单级减速
4. Brakes制动器：Service brakes:Hydraulically-actuated, wet disc brakes actuate
on four wheels行车制动器：液压驱动，四车轮湿式盘式制动；Parking brake: Wet, multi-disc brake on transmission output shaft驻车制动器：变速箱输出轴湿式多片制动
5. Steering System转向系：Type：Articulated type, full-hydraulic power steering类型：铰接式，全液压动力转向；Steering angle：40° each direction转向角：各个方向40°；Minimum turning radius at the center of outside tire外轮中心最小转弯半径
6. Boom and Bucket动臂和铲斗：
Z-bar loader linkage is designed for maximum rigidity and offers powerful breakout.
Z型连杆设计提供了最大的刚性和强大的破坏力。
Rap-out loader linkage design enables shock dumping for removing sticky materials.
敲打型连杆设计提供了粘性材料的振动装卸。
Sealed loader linkage pins with dust seals extend greasing intervals.
防尘密封式连干销延长了润滑间隔时间。
The bucket is made of high-tensile strength steel.
铲斗由高抗拉强度钢制做。
7. Bucket Controls铲斗控制：
The use of a PPC hydraulic control valve offers lighter operating effort
for the work equipment control levers.
应用液压程序控制阀使工作装置操纵杆操作轻便。
The reduction in the lever force and travel makes it easy to operate in the work envi- ronment.
操纵杆作用力和行程的减小使工作装置的操作变得容易。
Control positions位置控制：Boom：Raise, hold, lower, and float动臂：提升，保持，下降，浮动；Bucket ：Roll back, hold, and dump铲斗：后倾翻，保持，倾卸
8. Hydraulic System液压系统：Capacity (discharge flow) engine-rated rpm发动机额定转速容量（流量）：Loader pump装载机液压泵；Steering pump转向泵；Pilot pump(Gear-type pumps)引导泵（齿轮泵）；Relief valve setting安全阀设定压力；Control valve：2-spool open center type控制阀：双阀芯开式中心型；Hydraulic cylinders：Double-acting, piston液压缸：双作用，活塞；Hydraulic cycle time (rated load in bucket)：Raise，Dump，Lower (empty)，Total cycle time液压循环时间：提升时间，倾卸时间，下降时间，总循环时间
8.2.7 Dimensions尺寸规格
8.2.7.1Wheel Loader轮式装载机
1. Height to top of ROPS 倾翻保护驾驶室顶部高度；
2. Height to top of exhaust pipe 发动机排气管道顶部高度；
3. Height to top of hood 机罩顶部高度；
4. Ground Clearance 离地间隙；
5. B-Pin height at max. height
最大铲斗铰点高度；6. Center line of rear axle to edge of counterweight 后轴至配重边沿中心距；7. Wheelbase 轴距；8. B-Pin height at carry position铲斗铰点运输高度；9. Center line of rear axle to hitch 后轴至车架铰销轴中心距；10. Rack back at maximum lift 最大提升高度铲斗后倾角；11.Dump angle at maximum lift 最大提升高度铲斗卸载角；12. Rack back at carry position 铲斗运输位置后倾角；13. Rack back at ground    铲斗地面位置后倾角；14.Height to center line of axle 中心轴线高度；15. Bucket reach 卸载距离；16. Dump clearance at 45° full height 卸载角45°时的最大卸载高度
8.2.7.2Track-Type Loader履带式装载机
1. Overall machine width with bucket机械总宽度（包括铲斗）；
2. Overall machine width without bucket机械总宽度（不包括铲斗）；
3.Machine height to top of cab机械驾驶室顶部高度；
4.Length to front of track履带长度；
replaceable5.Overall machine length机械总长度；
6.Digging Depth铲掘深度；
7.Maximum rollback at carry position运输位置最大后倾角；
8.Reach at full lift height最大高度卸载距离；9.S.A.E. specified dump angle S.A.E. 标准卸载角；10.Maximum rollback, fully raised最大提升高度时的最大后倾角；11.Dump clearance at full height and 45° discharge最大高度45°卸载角时的卸载高度；12.Height to bucket hinge pin铲斗铰销高度；13.Overall machine height, bucket fully raised铲斗最大提升高度时
的机械最大高度。
8.2.8 Bucket Features铲斗特点
1. Edge steel with extra hardened and toughened wear plates of up to 500 Brinell gives the bucket longer operating life.
铲斗棱边为超硬耐磨钢板，布氏硬度达到500，具有较长的使用寿命。
2.Bucket shell and side plates of up to 400 Brinell to withstand abrasive wear. Reinforced mounting points where the attachment is installed give less wear.
铲斗壳体与侧板的布氏硬度达400，以抵抗磨料磨损。经强化处理的附件安装铰点减少了磨损。
3.Bucket cutting edges of abrasive-resistant steel of up to 500 Brinell. Replaceable bolt-on wear plates on bucket floor,500 Brinell.
铲斗切削刀刃为抗磨料磨损钢材，布氏硬度达500。铲斗底板上安装有耐磨衬板，由螺栓紧固可更换，布氏硬度为500。
4.Bolt-on edge savers and segments protect the cutting edge from unnecessary wear.
螺栓紧固的边缘节省块和分段防止了切削刃的不必要磨损。
5.Volvo Tooth System with bolt-on or weld-on adapters of up to 515 Brinell gives excellent penetration and less bucket wear.
沃尔沃斗齿系统配备有螺栓紧固型或焊接型连接器，布氏硬度达515，具有最佳的插入深度和较小的磨损。
8.2.9Skid-steer Loader Features滑移装载机特点
1.The round-back bucket design is stronger with no angled corners. This configuration makes it easier to fill and dump — improving productivity.
圆弧底铲斗设计更加坚固，没有死角。这种结构使铲斗更加容易装载和倾卸物料，从而提高了生产率。
2.The ROPS/FOPS structure protects and shields the operator.
防倾翻/防落物驾驶室结构保护了驾驶员的安全。
3. A total of four exterior lights help to illuminate any job site day or

版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系QQ:729038198，我们将在24小时内删除。