Designation: F 1554 – 07a
Standard Specification for
Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength1
This standard is issued under the fixed designation F 1554; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1.  Scope
1.1 This specification covers straight and bent, headed and headless, carbon, carbon boron, alloy, or high-strength low-alloy steel anchor bolts (also known as anchor rods).  The Anchor bolts are furnished in three strength grades, two thread classes, and in the sizes specified in Section 4.
    1.2 The anchor bolts are intended for anchoring structural supports to concrete foundations.  Such  structural  supports include building columns, column supports for highway signs, street  lighting  and  traffic  signals,  steel  bearing  plates,  and
similar applications.
1.3 Supplementary requirements are included to provide for Grade 55 weldable steel，permanent manufacturers and grade identification, and impact properties for Grades 55 and 105.
    1.4 Zinc coating requirements are included in Section 7 for Applications requiring corrosion protection.
1.5 The recommended grade and style of nut and washer are included in 6.6 and 6.7 for each grade.
1.6 This specification does not cover the requirements for mechanical expansion anchors, powder-activated nails or studs, or anchor bolts fabricated from deformed bar.
1.7  The values stated in inch-pound units are to be regarded as  the  standard.  The  values  given  in  parentheses  are  for information only.
2.  Referenced Documents
2.1  ASTM Standards:
A 194/A194M Specification for Carbon and Alloy Steel Nuts for Bolts for High-Pressure and High-Temperature Service3
A 370 Test Methods and Definitions for Mechanical Testing of Steel Products4
include中文A 563 Specification for Carbon and Alloy Steel Nuts5
A 673/A673M Specification for Sampling Procedure for Impact Testing of Structural Steel6
A 751  Test  Methods,  Practices,  and  Terminology  for Chemical Analysis of Steel Products4
B 695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel7
D 3951 Practice for Commercial Packaging8
F 436 Specification for Hardened Steel Washers5
F 606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets5
F 2329 Specification for Zinc Coat. Hot-dip. Requirements for Application to Carbon and Alloy steel Bolts Screws. Washer. Nut, and Alloy Steel Bolts, Screws, Washer, Nuts, and Special Threaded Fastener.
设计规范：F 1554 – 99
本规范适用屈服强度为36，55和105ksi（248,380和725MPa）的锚栓
本规范根据设计规范F 1554发布：规范里面数据是设计规范最初数据或者最近修改数据。括号中的数据标明最近认可的年份。上角标表示最近的修改认可。
1.适用范围
1.1 本规范适用直的和弯的，带头和不带头，碳钢或者碳磞钢，合金钢，或者高强度低合金锚栓（即锚杆）。提供的锚栓根据3个强度等级，两个螺纹等级，和尺寸在第4章进行分类。
1.2 这种锚栓或者锚杆指的是锚固支撑在混泥土上的构件，比如建筑物的柱子，高速公路指示牌，信号灯，路灯的支撑柱，垫板或者类似的构件。
1.3 对于55级（380MPa）可焊接钢材有其他附加要求，55级（380Mpa）和105级（725MPa）共同附加要求包括：永久性的强度标签，制造商标签和抗冲击试验的要求.
1.4 对于使用要求防腐的有镀锌要求见第7章
1.5 在6.6和6.7章节分别对螺母和垫圈强度和样式做出了推荐性的建议。
1.6 本规范没有包括：机械膨胀锚栓，由钢棒轧制而成的铆钉，碳粉激活双头锚栓或者锚杆。
1.7 所有数值均以英制数值为标准，括号里标注的数值仅供参考
2. 参考文献
2.1 ASTM标准
A 194/A194M  Specification  for  Carbon  and  Alloy  Steel
    Nuts for Bolts for High-Pressure and High-Temperature
    Service3
A 370  Test Methods and Definitions for Mechanical Testing of Steel Products4
A 563  Specification for Carbon and Alloy Steel Nuts5
A 673/A673M  Specification  for  Sampling  Procedure  for Impact Testing of Structural Steel6
A 751  Test  Methods,  Practices,  and  Terminology  for Chemical Analysis of Steel Products4
B 695  Specification  for  Coatings  of  Zinc  Mechanically Deposited on Iron and Steel7
D 3951 Practice for Commercial Packaging8
F 436 Specification for Hardened Steel Washers5
F 606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets5
F 2329 Specification for Zinc Coat. Hot-dip. Requirements for Application to Carbon and Alloy steel Bolts Screws. Washer. Nut, and Alloy Steel Bolts, Screws, Washer, Nuts, and Special Threaded Fastener.
2.2    Research Council on Structural Connections Standard9:
Specification  for Structural  Joints  Using ASTM A325  or A490 Bolts
2.3    ANSI/ASME Standards:10
B 1.1 Unified Screw Threads
B 1.3 Screw Thread Gaging Systems for Dimensional Acceptability

版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系QQ:729038198，我们将在24小时内删除。