3．将电调接上电池。
4. 如果连接正确，LCD 屏幕则显示出 开机界面，此时按压“ ”或“ ”键，编程
卡将显示界面 ，等待几秒后，显示第一个参数设置界面，则表示编程卡与电调 连接成功。使用“ ”、“ ”与“ ”按键更改参数，按“ ”键保存参数。
说明书
产品特点
1. 作为独立的设备，利用自带的LCD(液晶屏幕)显示电调参数，进行参数设定。
2. 将电池连接编程卡右侧接口，检测电池整体电压及每节电池的单体电压。
3. 针对中特威有数据回传功能的电调，能够显示实时数据，包括: 电压、电流、输入油门、输出油门、转 速、电池电量、MOS温度与电机温度。
4. 针对中特威有数据记录功能的电调，可读取数据记录值，包括: 最大转速、最小电压、最大电流、外 部温度、最高温度。
5. PWM油门信号检测：识别并显示输入油门脉宽及频率。
6. 油门调速器: 通过编程卡按钮，调整油门信号，对舵机、电调等设备进行油门控制。
7. 可通过中特威蓝牙模块连接手机App对编程卡进行升级。
规格
外形尺寸: 84*49*11.5mm 重量:40g 供电电源:DC5~12.6V
使用范围
1. Beatles G2、Mantis G2、Skyhawk系列航模无刷电调。
2. Shark G2、Seal G2、Dolphin系列船模无刷电调。
1. 断开电调电源。
2. 选择相应的连线方式，将电调与编程卡连接好。 如果电调编程线与油门线复用，则从接收机上拔出电调油门线，按照正确的顺序插入LCD编程卡 的“ESC”插口中。 如果电调有独立的编程口，则使用编程连接线将电调的编程口与LCD编程卡的“ESC”端口连接好。按键与各插头功能说明
使用说明
一、 作为独立设备对电调进行参数设定
注：
1. 使用LCD编程卡将电调参数恢复成出厂默认值 在电调和LCD编程卡联机状态下，多次按“ITEM”键，直至显示“Restore Default”，按OK键，则将电 调的所有参数恢复成出厂默认值。
2. 使用LCD编程卡读取电调数据记录值 针对中特威有数据记录功能的电调，在菜单“Restore Default”后面，可显示以下数据：最大转速、最 小电压、最大电流、外部温度、最高温度。(无数据记录功能的电调，则不会显示这些数据)
3. 使用LCD编程卡实时查看电调运行数据 针对中特威有数据回传功能的电调，在电调和LCD编程卡联机状态下: LCD编程卡能够实时显示以下数据: 电压、电流、输入油门、输出油门、转速、电池电量、MOS温度 与电机温度。 如果电调出现错误状态，LCD编程卡会循环显示当前错误，错误对应如下:
二、 PWM油门信号检测
连接PWM输出信号设备与LCD编程卡，且在联机状态下，同时长按 键3秒进入调试界面，选择1. : 循环切换编程项目。
2. : 正方向循环切换某编程项目的参数值。
3. : 反方向循环切换某编程项目的参数值。
4. : 保存并发送当前所选的参数值到电调。
5. ESC : 信号线接口，
电调的编程线与此接口相连。6. Batt : 编程卡供电输入接口，当电调无电压输出时（如OPTO电调，需要使用一个独立的电池或 UBEC从该接口给LCD编程卡供电。7. Battery Check : 电池检测接口，用于检测电池整体电压及每节电池的单体电压。
尊敬的客户，感谢您购买和使用本产品，使用前请认真阅读此说明书！中特威多功能LCD 编程卡G2是一款集多种功能于一身的编程卡，LCD液晶屏幕显示，功能丰富，直观易懂，迷你尺寸，小巧便捷，非常方便携带在外场使用。
三、 油门调速器
通过编程卡按钮，调整油门信号，对舵机、电调等设备进行油门控制。 同时长按 键3秒进入调试界面，选择“Output Signal”。 分别按下 键，油门宽度将以“1us”为单位进行加减，长按 或 键3秒左右可对油门进 行快速加减。 按下“ITEM”键，油门宽度将以“100us”为单位进行减少，按下“OK”键，油门宽度将以“100us”
为单位进行增加。
因为电调功能持续更新，所以LCD编程卡的固件程序也需随之更新，必要时我们需对LCD编程卡的固件程序进行升级，方法如下:1. 使用电调、电池或者外部电源设备给LCD编程卡单独供电，供电范围5-12.6V。2. 将中特威蓝牙模块(需单独购买)跟LCD编程卡“ESC”端口连接。3. 下载中特威航模APP，打开手机蓝牙，到“ZTW-BLE-XXXX”，点击连接。4. 连接成功后，选择“Firmware”，再选择“Firmware Update”。5. 选择最新固件，点击“OK”进行升级。6. 等待数秒，直到界面显示“升级成功”即可。112123
2ZTW
PB-G2-V1.00
ESC CONNECTING
SC Protection Break Protection Loss Protection Zero Protection LVC Protection Temp Protection Start Protection OC Protection PPM_THR ERROR UART_THR ERROR UART_THR LOSS CAN_THR LOSS BAT_VOT ERROR
短路保护电机断线保护油门丢失保护
上电油门未归零保护低压保护温度保护启动堵转保护电流保护
PPM油门不在范围UART油门不在范围UART油门丢失CAN油门丢失
电池电压不在范围
地址：深圳市宝安区西乡街道九围新村冠锋工业园一栋二楼
电话: +86 755 29120026, 29120036, 29120056 传真: +86 755 29120016
网址:woem邮箱:******************
五、 LCD编程卡固件程序更新
Press and hold the buttons for 3 seconds at the same time, then select "Output Signal". Press the button respectively , the throttle will be increased or decreased in units of “1us”, long press the or button for about 3 seconds to quickly increase or decrease the throttle. Press the "ITEM" button, the throttle will decrease in units of "100us", press the "OK" button, the
throttle will increase in units of "100us".
ESC successfully. Press the “ ” “ ” and “ ” button to select the options, press “ ” button to save data.
4. If the connection is correct, LCD program box shows initial screen, press
“ ” or “ ”button on the LCD program box, the screen shows ，
then it shows the 1st programmable item after a few seconds, which means LCD program box connects with 1. : Change the programmable items circularly.
2. : Change the programmable items circularly in positive direction.
3. : Change the programmable items circularly in negative direction.
4. : Save and send the current parameters into the ESC.
5. ESC : Use programming line to connect this port with programming port of ESC.
6. Programming box power supply input port : When the programming port of ESC has no voltage output such as OPTO ESC, a separated battery or UBEC is needed to supply power for LCD programming box from this port.
7. 1. Disconnect the battery from the ESC.
2. Select the corresponding connection method, and connect the ESC with LCD program box. If the programming line of ESC shares a same line with throttle line, then unplug throttle line from
receiver and plug into “ESC” port of LCD program box correspondingly. If the ESC has independent programming port, then using programming line to connect
programming port of ESC with “ESC” port of LCD program box.3. Connect the ESC to battery.
Thanks for purchasing the LCD program box G2 , please read this manual carefully before using it.The ZTW Multifunction LCD G2 program box G2 is the equipment that integrates multiple
functions, it is small to carry and convenient to set parameters for ESC(Electronic Speed Controller).
1. Working as an individual device to set the parameters for the ESC.
2. Working as a Lipo battery voltmeter to measure the voltage of the whole battery pack and each cell.
3. For the ZTW ESC with data returning feature, it can display real-time data including: voltage, current, input throttle, output throttle, RPM, battery power, MOS temperature and motor temperature.
4. For the ZTW ESC with data logging feature, it can read the data including: maximum RPM, minimum voltage, maximum current, external temperature, and maximum temperature.
5. PWM throttle signal detection: Identify and display the input throttle pulse width and frequency.
6. ESC/Servo Tester: It works like remote control to adjust the speed for ESC/servo by press the program
五大编程appbox’s button.
7. The LCD program box can be upgraded by the mobile App via the ZTW bluetooth module.Size: 84*49*11.5mm Weight: 40g Power supply: DC5~12.6V
1232112ZTW
PB-G2-V1.00
ESC CONNECTING SC Protection
Break Protection Loss Protection Zero Protection LVC Protection Temp Protection Start Protection OC Protection PPM_THR ERROR UART_THR ERROR
UART_THR LOSS CAN_THR LOSS BAT_VOT ERROR
Short circuit protection
Motor wire brake protection Throttle loss protection Throttle is not in zero position when powered up Low voltage protection
Temperature protection Start locked rotor protection Over currect protection The PPM throttole is not in the range The UART throttle is not in the range
UART throttle loss CAN throttle loss
The battery voltage is not in the range
User Manual
FEATURES
SPECIFICATION
SUITABLE FOR THE FOLLOWING ESC
1.Beatles G2、Mantis G2、Skyhawk
2.Shark G2、Seal G2、Dolphin
DESCRIPTION OF EACH BUTTON AND PORT
INSTRUCTIONS
A. Working as an individual device to set the parameters for the ESC
The LCD program box should be updated because the functions of ESC are improved continously, the method is as follows:
1. Provide power for LCD program box by ESC, battery or external power supply device, the power supply range is 5-1
2.6V.
2. Connect the ZTW Bluetooth module to the "ESC" port of the LCD program box.
3. Download ZTW APP and install it on your phone, after install it successfully, open your phone’s bluetooth, find “ZTW-BLE-XXXX”, then click “Connect” .
4. After the connection is successful, select "Firmware", then select "Firmware Update".
5. Select the latest firmware and click "OK" to upgrade.
6. Wait for a few seconds until the interface displays "Upgrade Successful"
1. Reset the ESC by the LCD program box
When the connection between ESC and LCD program box is successfully established, press “ITEM” button for several times until the “Restore Default” is displayed, press “OK” button, then all programmable items in the current profile are reset to factory default options.
2. Read the data logging of ESC by LCD program box
For the ESCs with data logging function, the following data can be displayed after the menu of "Rest
ore Default": maximum RPM, minimum voltage, maximum current, external temperature, and maximum temperature. (ESCs without data logging function will not display these data)
3. Check the ESC running data in real time by LCD program box
B. PWM throttle signal detection
For the ESCs with data returning function, when the connection between ESC and LCD program box is successfully established:
When the PWM signal device such as the receiver is in normal working state, connect the receiver and LCD program box, Press and hold the buttons for 3 seconds at the same time, Then select “Input
, it can identify and display the input throttle pulse width and frequency.
C. ESC/Servo Tester
It works like remote control to adjust the speed for ESC/servo by press the program box’s button.
The LCD program box can display the following data in real time: voltage, current, input throttle, output throttle, RPM, battery power, MOS temperature and motor temperature.If the ESC has errors, the LCD program box will display the current error circularly. The errors are as
below:Shenzhen ZTW Model Science & Technology Co.,Ltd
ADD: 2/F, Block 1, GuanFeng Industrial Park, Jiuwei, Xixiang, Baoan, Shenzhen, China, 518126
TEL:+8675529120026,29120036,29120056FAX:+woemEMAIL:******************
For OPTO ESC, a separated battery or UBEC is needed to supply power for LCD
版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系QQ:729038198，我们将在24小时内删除。
发表评论