71-5405-250
8/02
Lionel StationSounds Heavyweight Diner Owner’s Manual
featuring
and
Table of contents
Congratulations!
C
ongratulations on your purchase of the Lionel StationSounds Heavyweight Diner with a fully detailed interior. This passenger car is equipped with realistic StationSounds and authentic interiors with figures.
The Lionel StationsSounds Diner is designed for use on conventional or Command layouts. It will nego
tiate most O-42 layouts, but O-54 or wider is
recommended for optimum performance. The RailSounds effects include:•Brake Sounds:Triggered by the BRAKE command (Command mode only–the car must be in motion).
•Brake Let-Off Sounds:Triggered by motion and stops in both Command and conventional modes, or by direction changes in Command mode.
•Rail Clatter:This feature accurately recreates the sound of car wheels passing over rail segments, timed to the speed of the car. It is triggered by motion in Command and conventional modes.•StationSounds:Unique departure,arrival and other announcements
activated from your CAB-1 in Command mode, and triggered by short
horn/whistle blasts in conventional mode.
Transformer operations
Coupling your Heavyweight Passenger Cars
3Turning on the lights in your Heavyweight Passenger Cars 4Conventional operation of StationSounds
5TrainMaster Command operations Command Control operation of StationSounds 6StationSounds command table 7Sample scripts
8-10CAB-1 numeric keypad commands for your StationSounds Car  11Assigning your StationSounds Car a new ID#
12Reprogramming the circuit boards to restore features 13Maintaining and servicing your StationSounds Car Replacing the lamps in your Heavyweight Passenger Cars 14-15Limited Warranty/Lionel Service
16
The following Lionel marks may be used throughout this instruction manual and are protected under law.  All rights reserved.
Lionel ®, TrainMaster ®, Odyssey ™, RailSounds ™, CrewTalk ™, TowerCom ™, DynaChuff ™,StationSounds ™, Pullmor ®, ElectroCoupler ™, Magne-Traction ®, CAB-1 Remote Controller ®,
Powermaster ®, Lionel ZW ®, ZW ®
E ach Heavyweight Passenger Car features
two operating couplers. Figure 1 illustrates the location of the uncoupling mechanisms on your cars. To open the couplers, position the truck on a Remote-Control or Uncoupling Track section (available separately,  6-65530 for O gauge,or 6-12746 or 6-65149 for O-27 gauge) so that the center pair of wheels is directly above the magnet in the track. Once the car is in place, press UNCOUPLE on the track controller to activate the Remote-Control or Uncoupling Track section, releasing the coupler.
Coupling your Heavyweight Passenger Cars
Turning on the lights in your Heavyweight Passenger Cars
include和contain
Conventional operation of StationSounds
I n conventional mode, short horn/whistle blasts (under one second) are used to activate the StationSounds announcements. StationSounds will only activate while the car is stopped. Table 1 below describes how StationSounds responds in conventional mode.
Trigger Car Speed Timing Effect
Short Horn/ Stop Within 15 seconds Station Arrival Announcement, Whistle Blast of stopping Conductor Exit Announcement
(“Watch your step.”) Short Horn/Stop Over 15 seconds Station Departure Announcement, Whistle Blast since stop Conductor Boarding Announcement
(or on first power-up)(“All Aboard!”)
Use the volume control knob on the bottom of the car (see Figure 4 on page 12) to set the volume to your desired level.
Some announcements contain random phrases and pauses. You will note some
variation during operation.
Table 1. StationSounds responses

版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系QQ:729038198，我们将在24小时内删除。