那些常见的注塑缺陷、不良点怎么用英语表达？
注塑、模具专业英语 
∙Surface Appearance 外观 
∙Glossiness/gloss finish 光洁度、粗糙度 
∙Matt finish/matt surface 毛面 
∙Glass fiber rich surface/glass emergence on the surface 玻纤外露、浮纤 
∙Blooming/surface blooming 表面析出 
∙White patches on surface 表面白斑 
∙Silver marks/silver streak 银纹 
∙Splay mark 水纹、料花 
∙Flow mark 流纹 
∙Brittle/brittleness 脆、脆性 
∙Bubbles/trapped gas 气泡/困气 
∙Void 孔、气泡 
∙Burn marks 烧伤 
∙FR failed 阻燃不合格 
∙Flame rating V-2 
∙阻燃等级V-2 Poor dispersion 分散不好 
∙FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块 
∙Pellet porous 颗粒料孔隙
∙Low impact/tensile strength etc 低冲击强度/拉伸强度等 
∙High flow/filler content etc 高流动性/过度填充 
∙Longs/fines/doubles 长粒/碎屑/连粒 
∙Poor cut 粒形不好 
∙Bristle/voids 表面有小气泡/孔 
∙Glass bundles 纤维结团 
∙Product was rejected due to  产品不能接受因为… 
∙High moisture level 高水分、高湿度 
∙Warpage/warped 翘曲/变形 
∙Shrinkage/shrink 收缩/收缩率 
∙Sink marks 凹陷、缩水 
∙Short shot/short molding 打不满、欠注 
∙Distortion 变形 
∙Over dimension 尺寸过大 
∙Under dimension 尺寸过小 
∙Flashing 飞边、披锋、溢边 
∙Discoloration 变 
∙Off color 颜差异 
∙Flow rate 流动速率 
∙Viscous/viscosity 粘性的、粘的/黏度 
∙High flow 高流动 
∙Low flow 低流动 
∙Sticky 粘的，粘性的 
∙Sticking core 粘后模，粘模芯 
∙Sticking sprue 粘水口 
∙Sticking cavity 粘前模 
∙Mold release（agent） 脱模(剂) 
图：焦痕
∙Surface Appearance 外观 
∙Glossiness/gloss finish 光洁度、粗糙度 
submarine
∙Matt finish/matt surface 毛面 
∙Glass fiber rich surface/glass emergence on the surface 玻纤外露、浮纤 
∙Blooming/surface blooming 表面析出 
∙White patches on surface 表面白斑 
∙Silver marks/silver streak 银纹 
∙Splay mark 水纹、料花 
∙Flow mark 流纹 
∙Brittle/brittleness 脆、脆性 
∙Bubbles/trapped gas 气泡/困气 
∙Void 孔、气泡 
∙Burn marks 烧伤 
∙FR failed 阻燃不合格 
∙Flame rating V-2 
∙阻燃等级V-2 Poor dispersion 分散不好 
∙FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块 
∙Pellet porous 颗粒料孔隙、 
∙Low impact/tensile strength etc 低冲击强度/拉伸强度等 
∙High flow/filler content etc 高流动性/过度填充 
∙Longs/fines/doubles 长粒/碎屑/连粒 
∙Poor cut 粒形不好 
∙Bristle/voids 表面有小气泡/孔 
∙Glass bundles 纤维结团 
∙Product was rejected due to  产品不能接受因为… 
∙High moisture level 高水分、高湿度 
∙Warpage/warped 翘曲/变形 
∙Shrinkage/shrink 收缩/收缩率 
∙Sink marks 凹陷、缩水 
∙Short shot/short molding 打不满、欠注 
∙Distortion 变形 
∙Over dimension 尺寸过大 
∙Under dimension 尺寸过小 
∙Flashing 飞边、披锋、溢边 
∙Discoloration 变 
∙Off color 颜差异 
∙Flow rate 流动速率 
∙Viscous/viscosity 粘性的、粘的/黏度 
∙High flow 高流动 
∙Low flow 低流动 
∙Sticky 粘的，粘性的 
∙Sticking core 粘后模，粘模芯 
∙Sticking sprue 粘水口 
∙Sticking cavity 粘前模 
∙Mold release（agent） 脱模(剂) 
图:欠注
∙Antioxidant 抗氧剂 
∙Flame retardant agent 阻燃剂 
∙Heat stabilizer 热稳定剂 
∙Chopped glass fiber 短切玻纤 
∙Roving glass fiber 粗纱/长玻纤 
∙Glass beads 玻璃微珠 
∙Milled fiber 碾磨纤 
∙Molybdenum disulfide/moly/MoS2 二硫化钼 
∙Colorant 着剂 
∙Pigment 颜料 
∙Dye 染料 
∙Accepted product specification 接受产品规格 
∙Approved our product 认可我们的产品 Re-set spec 重新定标准 

版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系QQ:729038198，我们将在24小时内删除。