SS-I  CS-2459  09/01/06
Page 1 of 2
Features
•Sleek, low-profile design.
•Addressable-analog communica-tion.
•Stable communication technique with noise immunity.•Low standby current.
•Two-wire SLC connection.
•Rotary, decimal addressing (1 –99).
•Optional remote, single-gang LED accessory (RA400Z).
•Dual LED design provides 360°viewing angle.
•Visible bicolor LEDs blink green every time the detector is ad-dressed, and illuminate steady red on alarm.
•Remote test feature from the panel.
•Built-in functional test switch activated by external magnet.•Built-in tamper-resistant feature.•Sealed against back pressure.•Constructed of off-white
Bayblend®, designed to commer-cial standards, and offers an attractive appearance.
•94-5V plastic flammability rating.•SEMS screws for wiring of the separate base.
•Optional relay, isolator, or sounder bases.
•Backward-compatible.
Listings
Listings and approvals below
apply to the SS-I Intelligent Plug-In Ionization Smoke Detector. In
some cases, the detector may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status.•UL Listed: file S1195.•CSFM approved:file 7271-1288:168.
profile的中文意思
SS-I
Intelligent Addressable Plug-In Ionization Smoke Detector
Description
Gamewell’s intelligent Smart Scan TM  plug-in smoke detector with integral commu-nication provides features that surpass conventional de-tectors. Detector sensitivity can be programmed in the control panel software. Sen-sitivity is continuously moni-tored and reported to the
panel. Point ID capability al-lows each detector’s address
to be set with decade address switches, providing exact de-tector locations for selective maintenance when chamber contamination reaches an unacceptable level. The SS-I ionization detector  incorporates a unique single-source, dual-chamber design to respond quickly and dependably to a broad range of fires. The SS-I detector  is compatible with Gamewell’s 602, 610, 632, 654 and 658FACPS with a Smart Scan TM  SLC.
Installation
The SS-I plug-in detector uses a separate base to simplify installation, service, and maintenance. A special tool allows maintenance personnel to plug in and remove detectors without using a ladder.
Mount base on an electrical backbox which is at least 1.5" (3.81 cm) deep. Suitable mounting back boxes include:•  4.0"  (10.16 cm) square box.
•  3.5" (8.89 cm) or 4.0" (10.16 cm) octagonal box.•Single-gang box (except  for relay or isolator base).
•With B501BH or B501BHT base, use a 4.0" (10.16 cm) square box.•With B224RB or B224BI base, use a 3.5" (8.89 cm) octagonal box, or a 4.0"(10.16 cm) octagonal or square box.
NOTES: 1) Because of the inherent  supervision provided by the SLC loop, end-of-line resistors  are not required. Wiring “T-taps” or branches are permitted for Style 4(Class “B”) wiring. 2) When using relay or sounder bases , consult data sheet CS-2464 (SS-LI) for device limitations between isolator modules and isolator bases.
SS-I with SS-B6 base 6934pho1.jpg Bayblend® is a registered trademark of Bayer Corporation.
SS-I      CS-2459    09/01/06
Page 2 of 2
Gamewell-FCI 12 Clintonville Road Northford, CT 06472-1610Phone: 203-484-7161Fax: 203-484-7118www.gamewell-fci    A Honeywell Company © 2006 Gamewell-FCI
Product Line Information
ring Diagrams
Address dial on back of detector.

版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系QQ:729038198，我们将在24小时内删除。