有关翻译
关于英国软件GEARDESIGNPRO的准确翻译
齿轮参数：
PINION→小齿轮
WHEEL→大齿轮
Normal Module (mm) →法向模数
Pressure Angle (degrees) →法向压力角
Helix Angle (degrees) →分度圆螺旋角
Helix Hand→螺旋旋向（left 左/right 右）
radius软件Centre Distance (mm) →中心距
Face Width (mm) →齿宽
Edge Chamfer (mm) →齿端倒角（棱）
Desired Ratio →要求的传动比
Number of Teeth→齿数
Sum of Add. Shift Coeff.→总变位系数（法向）
Add. Shift Coeff.→单个齿轮变位系数（法向）
Add. Shift Distribution→变位系数分配
nominal Thickness →公称齿厚
Backlash (Normal) (mm) →侧隙（法向）
Backlash Distribution →侧隙分配
Finished Thickness →成品齿厚
Outside Diameter (mm) →外径
Outside Diameter Chamfer (mm)→齿顶倒角（棱）（修缘）
Root Diameter (mm) →齿根直径
Root Fillet Radius (mm) →（齿条刀具）齿顶圆角半径
Basic Rack Proportions →基本齿条参数（输入/标准/计算）
Basic Rack Addendum (/Module) →基本齿条齿顶高系数
Basic Rack Dedendum (/Module) →基本齿条齿根高系数
Root Fillet Radius (/Module) →（基本齿条）齿根圆角半径系数
Protuberance →齿条刀具齿顶触角宽度
Allow Outside Diameter Reduction →允许齿顶圆减小
Keep Pinion and Wheel Same →保持两齿轮齿顶高相同
计算结果：
      PINION小齿轮    WHEEL大齿轮
Number of Teeth→齿数
Normal Module (mm) →法向模数
Pressure Angle (degrees) →法向压力角
Helix Angle (degrees) →分度圆螺旋角
Helix Hand →螺旋旋向（left 左/right 右）
Reference Diameter (mm)→分度圆直径
Addendum Modification Coeff. →变位系数（法向）
Outside Diameter (mm) →外径
Outside Diameter Chamfer (mm)→齿顶倒角（棱）（修缘）
Root Diameter (mm) →齿根直径
Root Fillet Radius (mm) →（齿条刀具）齿顶圆角半径
Centre Distance (mm) →中心距
Face Width (mm) →齿宽
Edge Chamfer (mm) →齿端倒角（棱）
Form Diameter (mm) →渐开线起始圆直径
Base Diameter (mm) →基圆直径

Thickness (nominal transverse) (mm) →（公称端面）齿厚
Thickness (nominal normal) (mm) →（公称法向）齿厚
Thickness (finished transverse) (mm) →（成品端面）齿厚
Thickness (finished normal) (mm) →（成品法向）齿厚
Measurement Over Balls(finished) (mm) →跨棒距
Ball Diameter (mm) →量棒直径
Chordal Span (mm) (finished) →（成品）公法线长度
Number of Teeth to Span →跨齿数

Contact Ratio (Transverse) →端面重合度
Contact Ratio (Axial) →轴向重合度
Desired Ratio →要求的传动比
Actual Ratio →实际传动比

Backlash (Transverse) (mm) →端面侧隙
Backlash (Normal) (mm) →法向侧隙
Backlash (Radial) (mm) →径向侧隙
Backlash (Transverse circular) (mm) →端面圆周侧隙
Backlash (Normal Circular) (mm) →法向圆周侧隙

start of active Profile Diameter (mm) →有效齿廓起始直径
Lowest Single Tooth Contact (mm)  →单齿啮合最小直径
Highest Single Tooth Contact (mm)  →单齿啮合最大直径
End of Active Profile Diameter (mm) →有效齿廓终止直径


Transverse Pressure Angle (deg)  →端面压力角
Transverse Module (mm) →端面模数

Working Pitch Diameter (mm) →节圆直径
Working Normal Pressure Angle (deg) →法向啮合角
Working Transverse Pressure Angle (deg) →端面啮合角
Working Helix Angle (deg) →节圆螺旋角

Face Width Offset (mm) →齿宽调整
Active Face Width(mm) →有效齿宽

Base Radius to Form Radius (mm) →渐开线起始圆到基圆的距离
Form Radius to SAP Radius (mm) →有效渐开线起始圆到渐开线起始圆距离
Bottom Clearance / Module →顶隙系数
Normal EAP Thickness / Module →有效齿廓终止点法向厚度系数
Normal O.D. Thickness / Module →齿顶法向齿厚系数
Root Fillet Radius / Module →（齿条刀具）齿顶圆角半径系数

Base Helix Angle (degrees) →基圆螺旋角
Normal Base Pitch (mm) →法向基圆节距
Transverse Base Pitch (mm) →端面基圆节距

ISO Quality grade →ISO 精度等级
Single radial composite deviation (mm) →一齿径向综合公差
Total radial composite deviation (mm) →径向综合总公差
Single pitch deviation (mm) →单齿距公差
Total cumulative pitch deviation (mm) →齿距累积公差
Single tangential comp. deviation (mm) →一齿切向综合公差
Total tangential comp. deviation (mm) →切向综合总公差
Profile form deviation (mm) →齿廓形状公差
Profile slope deviation (mm) →齿廓倾斜极限偏差
Total profile deviation (mm) →齿廓总偏差的公差
Helix form deviation (mm) →螺旋线形状公差
Helix slope deviation (mm) →螺旋线倾斜极限偏差
Total helix deviation (mm) →螺旋线总偏差的公差

Tangential force (N) →圆周力
Radial force (N) →径向力
Axial force (N) →轴向力

版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系QQ:729038198，我们将在24小时内删除。