E  DIN 53160‐2:2010‐01                                      ‐‐‐ DRAFT ‐‐
Content          Page  Preface ................................................. .................................................. (3)
1 Scope ................................................ .................................................. . (4)
2 Normative References ............................................... . (4)
3 Terminology ................................................ .. (4)
4 devices and test equipment .............................................. (5)
5 reagents ................................................ .................................................. . (5)
6 Implementation ................................................ . (6)
7 Evaluation ................................................ .................................................. . (6)
8 Test report ................................................ .................................................. (6)
9 Precision ................................................ ..................................................    . (6)
References ................................................. .................................................. .    7
Preface
This draft standard was in the NPF / NAB‐Community Working Group NA 078‐00‐14‐01 GAK 'saliva and perspiration, "the NPF / NAB community working committee NA 078‐00‐14 GA developed" analytical methods for colorants.
To avoid misunderstandings, it is noted that the test is not according to this draft standard is the same as in DIN EN ISO 105‐E04 "Textiles ‐ Tests for color fastness ‐ Part E04: Colour fastness unit to perspiration (ISO 105‐E04: 1994); German version EN ISO 105‐E04: 1996 "drive specified test methods.
Changes
Compared with DIN V 53160‐2:2002‐10 following changes:
a)  Scope modified;
b)  Subpart re‐recorded;
c)  included in the section equipment and test equipment saran wrap;
d) Content revised editorially and adapted to the current design rules.
1 Scope
This draft standard specifies a method to examine the colour fastness of commodities compared sweat simulant. The procedure is designed especially for those commodities, which are intended or which is predictable that they are in use with the skin. Through the examination will determine whether the utility can pass from coloring on the skin.
This standard does not apply to goods which are intended for contact with food, as well as parts of consumer goods, which make their function colorants, or commodities, for which this is the case in its entirety.
NOTE Examples are mines of crayons and colored pencils.
The test method is applicable to all commodities, regardless of the method used for coloring (such as dyeing, staining, coating). A possible mechanical wear, such as free‐framing of a colored layer after mechanical abrasion of a top coat will not be considered.
2  Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only taken with respect issue.  For undated references, the latest edition of the reference publication (including amendments).
DIN 12 491, Laboratory glassware ‐ Vacuum Desiccators
DIN 12880, Electrical laboratory equipment ‐ ovens and incubators
DIN 55943, colorants ‐ Definitions
DIN EN ISO 4618, Paints and varnishes ‐ Vocabulary
DIN EN 20105‐A03, Textiles ‐ Tests for color fastness ‐ Part A03: Grey scale for assessing staining
DIN ISO 3696, Water for analytical purposes ‐ Requirements and tests
3  Terms
For the purposes of this document, the following terms.
3.1
Colourfastness
Transition of a colorant from being tested on the filter paper using a simulant
3.2
Colorants
Generic term for all coloring substances
NOTE  classification of colorants see DIN 55944th
[DIN 55943:2001‐10, 3.58]
3.3
Topcoat
last layer of a coating system
[DIN EN ISO 4618:2007‐03, 2108]
E  DIN 53160‐2:2010‐01                                      ‐‐‐ DRAFT ‐‐
4  Equipment and test equipment
4.1 filter paper for qualitative analysis of variable‐.
4.2  Tape, Clear, self adhesive plastic tape, approximately 12 mm wide.
4.3  foil, household foil.
4.4  Desiccator, 12491st DIN
4.5  oven, according to DIN 12880, suitable for an operating temperature of (37 ± 2) ° C.
5  Reagents
5.1  General
Unless otherwise specified, use only reagents for the sweat simulate with the quality of analytical and only water, the quality of purity of at least 3 to DIN ISO 3696 equivalent.
5.2  Composition of the sweat simulate with pH value of
6.5 ± 0.1
Table 1 ‐ sweat simulate
Reagents  Mass fraction g / l
Sodium chloride,
editoriallyurea,
lactic acid (> 88%, by weight)  5.0  1.0  1.0
Ammonium hydroxide solution (1%, by weight)  Adding up to a pH value of 6.5 ± 0.1
NOTE  The composition of the sweat simulate is the same as in DIN EN 1811 reference test method for determination of nickel from products intended to come into direct and prolonged contact with skin Schweißsimulanz set.
5.3  Preparation of Manufacture of sweat simulate
(1.00 ± 0.01) g of urea (5.00 ± 0.01) grams of sodium chloride and (1.00 ± 0.01) g of lactic acid in a 1000 ml beaker transfer. 900 ml of water and stir until all the added reagents are completely dissolved. The pH meter calibrated according to the manufacturer's instructions with buffer solution. Then the pH electrode in the solution, stir lightly and add ammonium hydroxide solution until a stable pH value is achieved from 6.5 ± 0.1. The solution to a 1000 ml volumetric flask transfer and fill with water up to the mark. Before use, the pH of the sweat simulate in the range of 6.5 ± 0.1.
The sweat simulate only on the day of production use.

版权声明:本站内容均来自互联网,仅供演示用,请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系QQ:729038198,我们将在24小时内删除。