组装、冲压、喷漆等专业词汇
Assembly line 组装线 Layout 布置图
Conveyer 流水线物料板
Electric screw driver 电动起子worktable 工作桌
Rivet table 拉钉机 Rivet gun 拉钉 bolt 螺栓Screw driver 起子 driller ??床barcode scanner 条码扫描器inner parts inspect 内部检查Pneumatic screw driver 气动起子 peda l踩踏板fasten 锁紧(螺丝)pallet 栈板 barcode 条码midfinger 中指 little finger 小指supervisor 课长 rear plate 后板fuse together 熔合
MT 制造生技 left fork 叉车cosmetic inspect 外观检查deputy manager | =vice manager 副理ME 制造工程师 chassis 基座Voltage switch of SPS 电源电压接拉键QC 品管 operator 作业员repair 修理 buzzle 蜂鸣器thumb screw 大头螺丝front plate 前板 Tiana 天那水EMI gasket 导电条forefinger 食指 die repair 模修
reset button 重置键Hi-pot test of SPS 高源高压测试department director 部长 be put in storage 入库 hydraulic machine 油压机
sheet metal parts 冲件material check list 物料检查表
SOP 制造作业程序
carton 纸箱 sub-line 支线personnel resource department 人力资源部 bezel panel 面板QC Section 品管科stamping factory 冲压厂 painting factory 烤漆厂 molding factory 成型厂 common equipment 常用设备uncoiler and straightener 整帄机
robot 机械手 lathe 车床production department 生产部门 planning department 企划部scraped |'skræpid|报废
planer |'plein|刨床plastic parts 塑胶件miller 铣床 grinder 磨床
special assistant manager 特助linear cutting 线切割
staker=reviting machine 铆合机factory director 厂长
position 职务 cleaning cloth 抹布
work cell 工作间 trolley 台车president 董事长 forklift 叉车deputy section supervisor =vice section superisor 副课长 group leader/supervisor 组长 line supervisor 线长 assistant manager 助理
to move, to carry, to handle 搬运
to unload materia l卸料 to return material/stock to 退料
power button 电源按键
speckle 斑点 deformation 变形
pack packing 包装to file burr 锉毛刺 final inspection 终检 to connect material 接料 to reverse material 翻料 wet station 沾湿台 to load material 上料 chain 链条deficient purchase 来料不良manufacture procedure 制程deficient manufacturing procedure 制程不良education and training 教育与训练 proposal improvement 提案改善trailer=long vehicle 拖板车name of department 部门名称
automatic screwdriver 电动启子defective to staking 铆合不良embedded lump 镶块
thumb 大拇指 stopper 阻挡器spare parts=buffer 备件
defective product label 不良标签 feeding is not in place 送料不到位stamping-missing 漏冲production capacity 生产力ring finger 无名指 cost 成本identifying sheet list 标示单compound die 合模 pressure plate=plate pinch 压板band-aid 创可贴 safety 安全thickness gauge 厚薄规 flow board 流水板hydraulic handjack 油压板车 forklift 叉车 fingers 割手套pallet 栈板 glove(s)手套glove(s) with exposed not up to standard 不合规格
head of screwdriver 起子头mop 拖把 welder 电焊机garbage container 灰箕vaccum cleaner 吸尘器
garbage can 垃圾箱 garbage bag 垃圾袋 magnetizer 加磁器production line 流水线to mop the floor 拖地 to clean the floor 扫地 lamp holder 灯架to clean a table 擦桌子
packaging tool 打包机
packaging 打包 wrong part 错件grease/oil stains 油污painting peel off 脏污 shrinking/shrinkage 缩水 mixed color 杂 power wire 电
dimension/size is a little bigger 尺寸偏大(小)operation procedure 作业流程
cosmetic defect 外观不良
mildewed=moldy=mouldy 发霉
slipped screwhead/shippery screw thread 滑手 gauge(or jig)治具burr (金属)flash (塑件)毛边 slipped screwhead/slippery screw head 螺丝滑头 air pipe 气管
poor processing 制程不良 scratch 划伤 basket 蝴蝶竺polishing/surface processing 表面处理 exposed metal/bare metal 金属裸露
fold of pakaging belt 打包带折皱 painting make-up 补漆 discoloration 羿water spots 水渍 subject 主题 die worker 模工
to repair a die 修模 packing material 包材 plastic basket 胶筐
engineering 工程 quality 品质
QC 品管 missing part 漏件
section sup
课长 fit together 组装在一起
administration/general affairs dept 总务部 die locker 锁模器 dents 压痕defective upsiding down 抽芽不良 screwdriver holder 起子插座 iudustrial alcohol 工业酒精excessive defects 过多的缺陷
enterprise plan = enterprise expansion projects企划 equipment设备lack of painting烤漆不到位to fix a die装模 cleanness清扫
stop/switch off a press关机die change 换模 culture教养deformation变形 to notice通知feeder送料机 board看板
qualified products, up-to-grade defective products, not up-to-grade products不良品 waste废料 products良品 sliding rack滑料架
isolating plate baffle plate; barricade隔板 carton box纸箱character die字模to feed, feeding送料 transportation运输
to put material in place, to cut material, to input落料 to impose lines压线to compress, compressing压缩(be)qualfied, up to grade合格
not up to grade, not qualified不合格to start a press开机evaluation评估 regulation整顿prepare for, make preparations for 准备 production unit生产单位
material change, stock change材料变更 feature change 特性变更 parameters参数rotating speed, revolution转速manufacture procedure制程
manufacture management制造管理abnormal handling异常处理lots of production生产批量to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈 automation自动化stage die工程模 shut die架模to stake, staking, reviting铆合feeder送料机uncoiler & strainghtener整帄机rack, shelf, stack料架add lubricating oil加润滑油vocabulary for stamping 冲压常词汇 die lifter举模器stamping, press冲压 punch press, dieing out press冲床
robot机械手 cylinder油缸taker取料机 inch寸动 conveyer belt输送带transmission rack输送架top stop上死点 scratch刮伤bottom stop下死点 dent压痕one stroke一行程 filings铁削 conservation清洁
to continue, cont.连动analog-mode device类模器shut height of a die架模高度to draw holes抽孔 inquiry, search for查寻 second count 复盘人to grip(material)吸料 location lump, locating piece, block stop 定位块reset复位 smoothly顺利 receive领取 upper die base上模座
processing, to process加工delivery, to deliver 交货to return send delinery back to retrn of goods退货 registration登记
registration card登记卡to control管制 tolerance工差to put forward and hand in提报safe stock安全库存
application form for purchase请购单consume, consumption消耗 failure, trouble故障to fill in填写 character die字模
abrasion磨损 statistics统计to take apart a die卸下模具to load a die装上模具to looser a bolt拧松螺栓
reverse angle = chamfer倒角easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂 to tight a bolt拧紧螺栓
to collect, to gather收集die 模具 punched hole冲孔to lubricate润滑figure file, chart file图档
模具工程常用词汇
progressive die, follow (-on)die 连续模 compound die复合模panel board镶块to cutedges=side cut=side scrap切边 to bending折弯
to pull, to stretch拉伸Line streching, line pulling线拉伸 to stake铆合engraving, to engrave刻印material for engineering mold testing工程试模材料
designing, to design设计folded block折弯块sliding block滑块 die block模块location pin定位销lifting pin顶料销 spring 弹簧
design modification设计变化die plate, front board模板padding block垫块 bolt螺栓lower die base下模座
upper padding plate blank上垫板 stepping bar垫条spare dies模具备品 work order工令casing = containerazation装箱document folder文件夹
to put file in order整理资料spare tools location手工备品仓first check初盘复棹人second check复盘复核人
quantity of customs count 会计师盘，点数量the first page第一联filed by accounting department for reference会计部存查
end-user/using unit(department)使用单位－(NHK厂区送财会部) first count初盘人plate电镀 inspected进货待验
summary of year-end physical inventory bills 年终盘点截止单据汇总表bill name单据名称blank and waste sheet NO. 空白与作废单号
This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部
Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表 location地点
not included in physical inventory不列入盘点sample样品 description品名 incoming material to be steel/rolled steel钢材
material statistics sheet 物料统计明细表meeting minutes会议记录score=groove压线distribution department分发单位
present members出席人员chairman主席 conclusion结论decision items决议事项responsible department负责单位
pre-fixed finishing date预定完成日production control confirmation生产确认 checked by初审 materials物料
approved by / checked by / prepared by核准/审核/承办 to be inspected or reworked待验或重工 total合计quantity of physical invetory second count 复盘点数量
PCE assembly production schedule sheet PCE组装厂生产排配表obsolete material良品已呆滞cause description原因说明
approved by核准stock age analysis sheet 库存货龄分析表 on-hand inventory现有库存 available material良品可使用physical count quantity帐面数量 notes说明 degrease脱脂
type形态 item/group/class类别quality品质 prepared by制表
year-end physical inventory difference analysis sheet 年终盘点差异分析表 physical inventory盘点数量
cause analysis原因分析difference quantity差异量disposed goods处理品warehouse/hub仓库
raw materials原料 finished product成品 semi-finished product半成品packing materials包材oversea location海外仓
good product/accepted goods/ accepted parts/good parts良品trim剪外边 pocket for the punch head挂钩槽 grit 砂砾
defective product/non-good parts不良品 skid/pallet栈板spare parts physical inventory list备品盘点清单 spare molds location模具备品仓
tox machine自铆机wire EDM线割 EDM放电机coil stock卷料 sheet stock片料 cover plate盖板pierce剪内边cam block滑块
pilot导正筒 drag form压锻差expansion dwg展开图torch-flame cut火焰切割set screw止付螺丝 form block折刀 stop pin定位销 bracket小磁导radius半径 molding成型slug hole废料孔 feature die公母模 shim(wedge)楔子 button圆冲子round pierce punch=die baffle plate挡块 dismantle the die折模shape punch=die insert异形子active plate活动板 female die母模 male die公模groove punch压线冲子stock locater block定位块
air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块 ctor系数 alkalidipping脱脂hromate铬酸处理
club car高尔夫球车 under cut=scrap chopper清角capability能力 parameter参数phosphate皮膜化成 viscosity涂料粘度
main manifold主集流脉bezel斜视规 blanking穿落模dejecting顶固模 D.I. rinse纯水次demagnetization去磁；消磁
alkaline etch龄咬 fillet镶；嵌边part number/P/N料号good products良品 assembly组装production tempo生产进度现状disposed products处理品
desmut剥黑膜 drill铝scraped products报放心品defective products不良品spline=the multiple keys花键
Anodize阳性处理 seal封孔 blinster气泡 short射料不足quenching淬火 tempering回火heat dissipation热传rack上料 boring镗 shank摸柄
barcode条码 volatile挥发性flow chart流程表单 poly-line多义线 convex凹 degate打浇口 concave击spare parts=buffer备品
induction light感应光 ram连杆cold slug冷块 cam driver铡楔titrator滴定仪 beacon警示灯heater band 加热片 dryer烘干机
response=reaction=interaction感应 derusting machine除锈机liaison联络单 resistance电阻 tungsten high speed steel钨高速的
edge finder巡边器 nick缺口 sand blasting喷沙 speck瑕?? gas mark焦痕shine亮班 splay 银纹 satin texture段面咬花coolant冷却液 crusher破碎机
gouge沟槽；凿槽 delamination起鳞 velocity速度witness line证示线grit沙砾 crank shaft曲柄轴
cushion缓冲 metal plate钣金 magnesium镁金 magnalium镁铝合金grit maker抽粒机through-hole form通孔形式
annealing退火 coordinate座标carbonization碳化alloy合金 thermocouple热电偶ion离子 stamping冲压moly high speed steel钼高速的
模具工程类
plain die简易模pierce die冲孔模 forming die成型模pin销 wire spring圆线弹簧progressive die连续模gang dies复合模
riveting die铆合模pierce冲孔 bending折弯forming成型(抽击，冲击)draw hole抽孔 emboss击点
trim切边 deburr or coin压毛边dome击圆 groove压线punch riveting冲压铆合side stretch侧冲压帄
tick-mark farside反面压印stamp letter冲字(料号)shearing剪断 blanking下料tick-mark nearside正面压印
lathe车procedure dwg工程图die structure dwg模具结构图material材质 factor系数material thickness料片厚度
press specification冲床规格die height range适用模高die height闭模高度burr毛边 weight重量
五金零件类
inner hexagon screw内六角螺钉 dowel pin固定销coil spring弹簧inner guiding post内导柱eq-height sleeves=spool等高套筒
guide pin导正销 outer guiding post外导柱 located pin定位销lifter guide pin浮升导料销stop screw止付螺丝 outer bush外导套 lifter pin顶料销
模板类
top block上垫脚 punch pad上垫板 top plate上托板female die母模(凹模) bottom block下垫脚 bottom plate下托板(底板) punch holder上夹板 stripper pad脱料背板 up stripper上脱料板male die公模(击模) feature die公母模 die holder下夹板
stripping plate内外打(脱料板) upper plate上模板lower plate下模板die set下模座 die pad下垫板 punch set上模座
lower stripper下脱料板
零件类
punch冲头 slag well冷料井insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子
special shape punch异形冲子round punch圆冲子bending block折刀roller滚轴 baffle plate挡块
supporting block for location 定位支承块bushing bolck衬套cover plate盖板 guide pad导料块air cushion plate气垫板
air-cushion eject-rod气垫顶杆 trimming punch切边冲子 stiffening rib punch = stinger 加强筋冲子 ribbon punch压筋冲子 reel-stretch punch卷圆压帄冲子
guide plate定位板sliding block滑块 active plate活动板 lower sliding plate下滑块板upper holder block上压块 upper mid plate上中间板spring box弹簧箱 spring-box eject-rod弹簧箱顶杆 spring-box eject-plate弹簧箱顶板
塑件&模具相关英文
compre sion molding压缩成型plsitive mold挤压式模具 split mold分割式模具 cavity型控 母模 core模心 公模 welding mark溶合痕
taper锥拔 leather cloak仿皮革shiver饰纹 flow mark流痕post screw insert螺纹套筒埋值
cylinder汽缸套 chip细碎物handle mold手持式模具striper plate脱料板 piston活塞
移转成型用模具
encapsulation molding低压封装成型
射出成型用模具
well type蓄料井 insulated runner绝缘浇道方式hot runner热浇道 cold slag冷料渣two plate两极式（模具）
h=0.02~0.05mm w=3.2mmL=3~5mm welding line熔合痕 sleave套筒spindle阀针spear head刨尖头 band heater环带状的电热器
eject pin顶出针knock pin顶出销return pin回位销反顶针stripper plate脱料板nozzle射嘴 slag well冷料井
insert core放置入子 runner stripper plate浇道脱料板guide pin导销 eject rod (bar)（成型机）顶业捧
subzero深冷处理 three plate三极式模具 runner system浇道系统stress crack应力电裂 orientation定向sprue gate射料浇口，直浇口
sprue lock pin料头钩销(拉料杆)tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口
dish gate因盘形浇口fan gate扇形浇口 sprue less)无射料管方式
H=F=1/2t~1/5t T=2.5~3.5mm diaphragm gate隔膜浇口ring gate环形浇口 subarine gate潜入式浇口
tunnel gate隧道式浇口pin gate针点浇口 Φ0.8~1.0mm Runner less无浇道 sprue浇口；溶渣
品质人员名称类
QC quality control 品质管理人员 FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员
OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员
POC passage quality control 段检人员 air vent排气道QA quality assurance 质量保证人员
QE quality engineering 品质工程人员
品质保证类
FAI first article inspection 新品首件检查TVR tool verification report 模具确认报告 3B 3B 模具正式投产前确认
CP capability index 能力指数CPK capability index of process 模具制程能力参数 corrective action report 改正行动报告
SSQA standardized supplier quality 合格供应商品质评估FA final audit 最後一次稽核
tablet press punch and dieOOBA out of box audit 开箱检查 8 disciplines 8项回复内容FMEA failure model effectiveness analysis 失效模式分析
FQC运作类
S/S Sample size 抽样检验样本大小AQL Acceptable Quality Level 运作类允收品质水准ACC Accept 允收
CR Critical 极严重的AOQ Average Output Quality 帄均出厂品质AOD Accept On Deviation 特采
AOQL Average Output Quality Level 帄均出厂品质 TYP Type 类型MIN Minor 轻微的S I-S IV Special I-Special IV 特殊抽样水准等级
Q/R/S Quality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准 MAJ Major 主要的
UAI Use As It 首件检查报告L/N Lot Number 特采
PPM Percent Per Million 批号FPIR First Piece Inspection Report 百万分之一
制程统计品管专类
SPC Statistical Process Control 统计制程管制AR Averary Range 全距帄均值LCL Lower Central Limit 管制下限
SQC Statistical Quality Control 统计品质管制
R Range 全距DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率
UCL Upper Central Limit 管制上限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测
其它品质术语类
QIT Quality Improvement Team 品质改善小组QCC Quality Control Circle 品质圈RMA Return Material Audit 退料认可
PDCA Plan Do Check Action 计划 执行 检查 总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善
QP Quality Policy 目标方针 QAN Quality Amelionrate Notice 品质改善活动
TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单 LQL Limiting Quality Level 最低品质水准
QT Quality Target 品质目标7QCTools 7 Quality Controll Tools 品管七大手法
通用之件类
PMP Product Management Plan 生产管制计划ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)
IS Inspection Specification 成品检验规范SOP Standard Operation Procedure 制造作业规范SIP Specification In Process 制程检验规格
BOM Bill Of Material 物料清单PCN Process Change Notice 工序改动通知PS Package Specification 包装规范 DWG Drawing 图面
系统文件类
QC Quality System 品质系统CGOO China General PCE龙华厂文件ES Engineering Standarization 工程标准
CMCS C-China M-Manufact C-Compaq S-Stamping CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范
CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范 部类S Stamping 冲压(厂)P Painting 烤漆(厂)
PPC Production Plan Control 生产计划控制 ISO International Standard Organization 国际标准化组织IWS International Workman Standard 工艺标准
MC Material Control 物料控制GS General Specification 一般规格 C Compaq (美国)康伯公司 A Assembly 组装(厂)
A/C Accountant Dept 会计部QE Quality Engineering 品质工程(部)PE Project Engineering 产品工程部
P/A Personal & Administration 人事行政部PD Product Department 生产部 P Painting 烤漆(厂)ME Manafacture Engineering 制造工程部
QA Quality Assurance 品质保证(处)S Stamping 冲压(厂)PMC Production & Material Control 生产和物料控制
QC Quality Control 品质管制(课)R&D Research & Design 设计开发部LAB Labratry 实验室IE Industrial Engineering 工业工程
生产类
PO Purchasing Order 采购订单SWR Special Work Request 特殊工作需求ID/C Identification Code (供应商)识别码
MO Manufacture Order 生产单D/C Date Code 生产日期码 PAL Pallet/skid 栈板 CTN Carton 卡通箱PRS Pairs 双(对等)
其它
OEM Original Equipment Manufacture 原设备制造
PCE Personal Computer Enclosure 个人电脑外设E-MAIL Electrical-Mail VS 以及 QTY Quantity 数量
PC Personal Computer 个人电脑 CPU Central Processing Unit 中央处理器NHK North of Hongkong 中国大陆 PRC People's Republic of China 中国大陆 SECC SEC SGCC SGCC 热浸镀锌材料 N/A Not Applicable 不适用U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的
版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系QQ:729038198，我们将在24小时内删除。
发表评论